Pages12
Year0
Language(s)
en
Share
of 12
of 12
Page 1
EN
AURES MULTI
INSTALLATION & OPERATION MANUAL
INSTANTANEOUS ELECTRIC WATER HEATER
Page 2
2
EN
GENERAL SAFETY INSTRUCTION 1. This manual is an integral part of the product. Keep it with in a safe place, and hand it on to
the next user/owner in case of change of property. 2. Read the instructions and warnings in this manual carefully, they contain important informa-
tion regarding safe installation, use and maintenance. 3. The appliance must be installed and commissioned by a competent person in accordance
with local legislation and health and safety regulations. All electrical power supply to the unit must be isolated and made safe before you open the terminal block.
4. DO NOT use the appliance for anything other than its specified use. The manufacturer is not liable for damage resulting from improper or incorrect use or failure to observe the instruc- tions given in this manual.
5. Incorrect installation can result in damage to property and injury to persons and animals; the manufacturer is not liable for the consquences.
6. DO NOT leave the packaging materials (staples, plastic bags, expanded polystyrene, etc.) within the reach of children - they can cause serious injury.
7. This appliance can be used by children aged from 3 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. DO NOT permit chil- dren to play with the appliance. User cleaning and maintenance may not be done by unsupervised children.
8. Any repairs, maintenance, plumbing and electrical connection must be done by qa com- petent person using original spare parts only. Failure to observe the above instructions can compromise the safety of the appliance and relieves the manufacturer of any liability for the consequences.
9. The hot water temperature is regulated by a thermostat which also acts as a safety device to prevent dangerous overheating.
10. The electrical connection must be done as indicated in this manual. 11. If the appliance is equipped with a power cable, the latter may only be replaced by an author-
ised service centre or professional technician. 12. Make sure to drain the appliance when it is out of service or in an area subject to subzero
temperatures. 13. Do not leave flammable materials in contact with or in the vicinity of the appliance. 14. DO NOT touch the appliance when barefoot or if any part of your body is wet 15. Before using the device and after routine maintenance, we recommend flushing the unit to
remove any debris . 16. Do not place anything under the water heater which may be damaged by a leak.
Page 3
3
EN
Symbol Meaning Failure to observe this warning can result in injury, which may even be fatal in certain circ*mstances
Failure to observe this warning can msult in damage or injury, even to property; plants and animals
Observe the product's general and specific safety instructions.
GENERAL SAFETY STANDARDS Ref. Warning Risk Symbol
1. Do not open the appliance or remove from its installation
Electrocution hazard due to the presence of live electrical equipment. Personal injury -overheated burns caused by components and wounds caused by sharp edges
2. Do not start or stop the appliance by inserting/ pulling the power plug
Electrocution hazard due to damage to the power cord, its plug or the socket
3. Do not damage the power cable Electrocution hazard due to bare live wires 4. Do not leave objects on the appliance Personal injury due to objects falling off the appliance as
a result of vibration Damage to the appliance or other property due to objects falling off the appliance as a result of vibration
5. Do not climb onto the appliance Personal injury due to falling off the appliance Damage to the appliance or other property due to the appliance itself detaching from its mounting
6. Do not clean the appliance without having first isolated the electrical power supply to the unit.
Electrocution hazard due to the presence of live electrical equipment
7. Install the appliance to a solid wall which is not subject to vibration
Danger of the appliance falling off the wall due to structural collapse
8. Make the electrical connection with cables of adequate cross-section
Danger of fire due to overheating of undersized electrical wires
9. Restore all safety and control functions after working on the appliance and check that they are operational before returning it to service
Damage or blocking of the appliance due to improper control
10. Drain all components containing hot water, using the bleed co*cks, before handling them
Danger of burns
11. Descale the system as given in the products "safety sheet"; when doing so, ventilate the room, wear safety clothing, make sure not to mix products, and protect the appliance itself and any adjacent objects
Personal injury due lo contact of the skin and eyes with add, inhalation or ingestion of noxious chemicals Damage to the appliance and adjacent objects due to corrosion by acid
12. Do not use insecticides, solvents or aggressive detergents to clean the appliance
Damage to plastic and painted parts and assemblies
Page 4
4
EN
TECHNICAL CHARACTERISTICS For the technical specifications, refer to the nameplate (the nameplate is located on the right side of the water heater).
PRODUCT INFORMATION Model AURES M 9.5 240V EU
Power (kW) 9.5
Voltage (V) 240
Phases Mono
Installation Multi point
Construction Close outlet
Frequency (Hz) 50/60
Electric current (A) 39.6
Electrical diagram III
Water Protection IP25
Pipe Connection 1/2" BSP
Minimum water flow (l/min) 2.1
Qelec (kWh) 2.224
Max water pressure 800 kPa (8 bar)
Load profile XS
Lwa (dB) 15
wh 39%
Rated Volume (l) 0.45
Weight (kg) 2.2
Dimensions (mm) 304 x 220 x 110
The power consumption data in the table and the other information given in the Product Data Sheet (Enclosure A to this manual) are defined in relation to EU Directives 812/2013 and 814/2013. The products without the label and the data sheet for water heaters and solar devices, stipulated in regulation 812/2013, are not intended to be used in such assemblies. Products equipped with a regulator knob have the thermostat positioned in the
Directives, of which it satisfies the essential requisites: - LVD Low Voltage Directive: EN 60335-1, EN 60335-2-35, EN 60529, EN 62233, EN 50106. - EMC Electro-Magnetic Compatibility: EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 61000-3-11 and EN 61000-3-12. - ERP Energy related Products: Eu812, Eu814, EN50193-1-2013
The UKCA marking of the appliances attests its conformity to the following UK legislation - Electromagnetic Compatibility Regulations 2016 - Electrical Equipment (Safety) Regulations 2016 - The Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019 - The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations
2012
Page 5
5
EN
Installation Instructions: The appliance must be installed and commissioned by a competent person in accordance with established regulations and local health and safety regulations.
240 mm
44 mm 20 mm
13 1 m
m
176 mm
1. Before performing any operations, disconnect the electricity using the external switch 2. Open the two screws located at the bottom of the device and remove the cover from base. 3. Fix the base horizontally against a wall or side of cabinet, the inlet and outlet water pipes are on the
down/bottom side of the unit. Use the four mounting screws provided.
cable
Flow restrictor AERATOR
Hot water out
Cold water in only
4. Use the supplied water filter on the inlet water pipe line (see diagram)
5. Connect the incoming cold water pipe to the inlet connection point on the bottom right side and the outgoing hot water pipe to the outlet water pipe on the bottom left side. Turn open the of water supply and check there is no water leakage from the unit.
6. Use an all pole switch conforming with national laws in force (contact gap of at least 3 mm, preferably equipped with fuses) to disconnect the appliance's power supply.
7. Connect the power cable to the terminal block inside the unit. The appliance must be earthed and the earth cable must be fixed to the terminal marked by the symbol .
8. Turn on the unit and check that it is operating as required. 9. Reconnect the cover to the base with 2 screws. 10. It is required that a Ground Fault Circuit Interrupter/Earth Leakage Circuit Breaker be incorporated in the circuit.
11. Make sure to install the pressure relief valve correctly (supplied with the product) before Inlet pipe.
12. It is required to install a flow control restrictor (AERATOR) at the sink or shower.
13. WARNING: UNIT MUST BE PROPERLY GROUNDED
14. THIS HEATER MUST HAVE ITS OWN INDEPENDENT CIRCUIT USING A CORRECTLY RATED CIRCUIT BREAKER AND SUITABLE WIRE, SEE TABLE RECOMMENDED CABLE.
Page 6
6
EN
INSTALLATION
OPERATING INSTRUCTIONS 1. Your new Instant Water Heater is flow activated. Regulate the knob in one of the 3 setting power (I, II,
III) the product will switch ON once the hot water tap is turned on, the heating element will work and warm the water only when there is a flow of water through the appliance.. You will need to allow at least 2.1 litres per minute to flow through the unit in order to activate the Instant Heating System. Run water through the heater for a few minutes.
2. Be sure to every so often clean the spray head to assure a smooth water flow. 3. Be sure to every so often clean the incoming water filter. 4. Be sure to install your Instant Water Heater in a heated location. The appliance cannot be installed in
areas where the temperature may drop critically and there may be a risk that ice may form. 5. The user can adjust the hot water temperature regulating the setting power on the unit. the user can
choose from 4 different power settings: - O - Heating element is off - I - Only the 1st Heating element switches on. - II - Only the 2nd heating element switches on. - III - 1st and 2nd heating elements switch on, working together.
INSTALLATION REQUIREMENTS A. A separate electrical supply is required. B. The device must be connected to a separate circuit breaker. C. The recommended electrical cable for supplying the device, see table I (next page)
WARNING! BEFORE BEGINNING ANY WORK ON THE ELECTRICAL INSTALLATION BE SURE THAT THE CIRCUIT BREAKER IS IN THE OFF POSITION TO AVOID DANGER OF ELECTRICAL SHOCK
Inlet and outlet at the bottom
Outlet Inlet
Incorrect InstallationCorrect Installation
See electrical diagrams at the end of the booklet.
ATTENTION The water inlet of this appliance must be connected directly to a cold water mains supply.
Page 7
7
EN
Power kW Loaded
Heating setting Recommended Cable
Recommended Fuse Rating220V 230V 240V
AURES M 9.5 240V EU -- -- 9.5 4.7+4.8 kW H05VV-F 3x6mm * 40A
Operating water pressure 50-800 kPa (0.5-8 bar) Water pressure operating power switch Standard 1/2" compression inlet connection Top-Left and Optional Top-right cable entry Bottom-right water entry
UNIT DIMENSIONS: HEIGHT 220mm WIDTH 304mm DEPTH 110mm
Table 1: Recommended cable
Power Knob Power LED Water Inlet
Pressure Relief Valve Filter
Water Outlet
* Recommended power cable size: 6mm2/10mm2 (in the UK 10mm2 is a requirement where it runs longer than 10 metres).
This product conforms to Directive WEEE 2012/19/EU.
The symbol of the crossed waste paper basket on the ap pliance indicates that at the end of its working life the pro duct should be disposed of separately from normal domestic household rubbish, it must be disposed of at a waste dispo sal center with dedicated facilities for electric and electronic appliances or
returned to the retailer when a new replace ment product is purchased. The user is responsible for the disposal of the product at the end of its life at an appropriate waste disposal center. The waste disposal center (which using special treatment and recycling processes effectively dismantles and disposes of the appliance) helps to protect the environment by recy cling the material from which the product is made. For further information about waste disposal systems visit your local waste disposal center or the retailer from which the product was purchased.
Page 8
8
EN
Troubleshooting
SYMPTOM POSSIBLE CAUSE SOLUTION
Water not hot enough
Too much water flowing through the heater
Reduction In the ambient temperature
Water Pressure below of 100 kPa
Electrical Malfunction
Reduce the flow rate of the water via the outlet tap.
Switch to higher temperature setting.
Check if the mains stop valve is fully open and that the there are no other restriction in the supply line.
Have the Heater unit checked by a qualified eIectrician or contact your local authorised distributor.
Water too hot Not enough Water flowing through the heater
Increase in the ambient temperature
Increase the flow rate via the outlet tap
Switch to lower temperature setting
Heater switch Off during use
Interruption of mains electrical supply
ELSD trip, possible earth leakage
Check incoming power supply, MCB, switches and supply cabling. Check earth leakage and reset ELSD
If problem persists, call your local authorised distributor for assistance.
Water ceases to flow
Blockage of spray head, twisted or blocked flexible shower hose.
No water supply.
Clean or replace spray head, check for free passage of water through hose. Replace as necessary.
Check water supply, stop valve Open? and no blockage.
Water temperature varies from hot to cold during use
Water pressure has dropped below min. level.
Increase hot water supply,
No hot water despite fully open hot water outlet
No electrical power
The activation flow rate needed to turn on the heating element has not been reached.
Check the circuit breaker and check voltage at the wiring block.
Clean filter screen Turn circuit breaker off Open hot valve to release pressure from
the unit. Turn circuit breaker on.
Page 9
9
ELECTRICAL WIRING
III NL
PO W
ER S
UP PL
Y 23
0V =F
1 - T
H ER
M O
ST A
T
=F 4
- H EA
TIN G
E LE
M EN
TS
=F 2
- P O
W ER
R EL
A Y
=F 5
- P O
W ER
L ED
-H .E .1
-H .E .2
-S 2
-S 1
-H 1
-H 2
-H 3
PC B
IN D
IC A
TO R
=F 6
- C O
M M
A N
D S
W ITC
H
=F 7
- R EE
D R
EL A
Y
-T 1
-R R
-K 1
-K 2
CZ 2
CZ 3
AC L1
57
C 85
C
85
C -R T1
-R T2
Page 10
10
EN
Product sizes
304 2
2 0
110
Optional cable entry Top-left cable inlet is for cable until 10 mm2
Optional top-right cable entry is only for power cable size: 6 mm2
Page 11
11
EN
Close cover Steps
A B
Close cover Steps
Page 12
Manufactured by: Ariston Thermo S.p.A. Viale Aristide Mer
